Foundation Weep Screed

AMICO Foundation Weep Screed provides a straight and true screed surface at the base of stucco walls, while allowing excess moisture to escape the back of the stucco membrane. It is important for the water-resistant backing paper and metal lath to overlap the nailing flange of the weep screed in order to guide the water to the exterior. Check with local building codes for the proper clearance above grade. This bead is required by most building codes in the United States.

Note: Unpunched Foundation Weep Screed has only a slotted nail hole punch out.

Certain sizes are available in brown, tan or grey.

Foundation Weep Screed

PRODUCT NO.
DIMENSIONS
GROUND
PCS. PER BOX
FOUNDATION WEEP SCREED AMFWS-425-500
414"
12"
30
FOUNDATION WEEP SCREED AMFWS-425-580
414"
58"
30
FOUNDATION WEEP SCREED AMFWS-425-750
414"
34"
30
FOUNDATION WEEP SCREED AMFWS-425-780
414"
78"
30

Standard Length: 10 Feet

Roof - Wall Screed

Roof – Wall Screed uses the same design as the Foundation Weep Screed, except it is manufactured with a shorter (2-3/8″) nailing flange. This design is ideal for roof-to-wall transitions found in both stucco and stone applications.

Roof - Wall Screed

PRODUCT NO.
NAIL FLANGE
GROUND
PCS. PER BOX
ROOF - WALL SCREED AMRWS-238-500
238"
12"
60
ROOF - WALL SCREED AMRWS-238-580
238"
58"
60
ROOF - WALL SCREED AMRWS-238-750
238"
34"
60
ROOF - WALL SCREED AMRWS-238-780
238"
78"
60
Mid-Wall Weep Screed

*Available in standard white, as well as tan, brown or gray (on exposed areas only).

Mid-Wall Weep Screed (Patent Pending) performs as an unpunched weep screed allowing excess moisture to escape the back of a stucco membrane. This screed also performs as an expansion (control) joint with twin grounds. It is installed where a framed stucco surface meets a masonry (concrete block) stucco surface. This condition is common between floors on 2-story homes and at the base of a gable receiving stucco.

The unpunched flange above must be installed extending at least one inch below the framing/ concrete joint. The weather barrier and lath should be installed over the solid upper flange to direct water to the foundation weep screed. The profile is manufactured with a 3½” nailing flange as required by code.

Mid-Wall Weep Screed

PRODUCT NO.
GROUND A
GROUND B
BOX COUNT
MID-WALL WEEP SCREED AMMWS-780-500
78"
12"
15
MID-WALL WEEP SCREED AMMWS-780-580*
78"
58"
15

Standard Length: 10 Feet

Weep Screed Extended Leg

Weep Screed Extended (Return) Leg is used like a regular foundation weep screed but covers the bottom edge of the sheathing in cases where the sheathing or framing extends beyond the edge of the foundation. This protects the edge of the sheathing from moisture and insect damage and closes the gap caused by the offset.

NOTE: Weep screeds are only required at the base of framed walls. This profile is manufactured with a 3½” vertical nailing flange as standard.

Weep Screed Extended Leg

PRODUCT NO.
GROUND A
GROUND B
BOX COUNT
WEEP SCREED EXTENDED LEG AMFWS-L-425-780
414"
78"
30

Standard Length: 10 Feet

Window & Door Drip Edge

AMICO Window & Door Drip Edge is used to provide added protection for system edges at the top of windows and doors. This product has a drip edge which helps direct water away from the building. A two-inch rear flange is provided.

Note: The AMWDE150-25 is available in Tan.

Window & Door Drip Edge

PRODUCT NO.
BOARD THICKNESS
FINISH THICKNESS
PCS. PER BOX
WINDOW & DOOR DRIP EDGE AMWDE75-16
34"
116"
100
WINDOW & DOOR DRIP EDGE AMWDE100-16
1"
116"
100
WINDOW & DOOR DRIP EDGE AMWDE150-16
112"
116"
80
WINDOW & DOOR DRIP EDGE AMWDE200-16
2"
116"
75
WINDOW & DOOR DRIP EDGE AMWDE100-25
112"
14"
70
WINDOW & DOOR DRIP EDGE AMWDE150-25
112"
14"
65